• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fiat Spare Key 500 Replacement Key Fob

If your 500 remote key fob isn't working, it's time to replace the battery. If you do replace the battery and it is still not working the issue could be elsewhere.

At United Locksmith, we specialize in making new keys for old automobiles. We have the tools as well as the parts required for this service.

Dead Coin Battery

A dead battery is the most common reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob has the battery of a coin-cell that will drain quickly if it is not utilized frequently enough. If your remote began to show signs of weakness such as a loss of range and stopped working completely it is likely that the battery is dead.

Metal clips hold the battery in place inside the key fob. If the clips aren't secure, they could cause contact problems that will prevent your remote from receiving power. Utilizing a small screwdriver, pry the clip that holds the retaining pin open to remove the current battery and insert a new one. Use a battery that has the same size, voltage and specification as the original.

The exposure to water can cause the key fob to corrode or become damaged. Even a brief bath in soapy water could harm the electronic chip in. It is recommended to keep your key fob in a dry location.

Water Damage

Damage to your water supply could be the reason behind your key fob not working properly. Key fobs are fitted with rubber seals that stop them from being damaged by light rain or splashes of water, however it is crucial to keep your keys out of the pool, ocean and washing machine!

The key fob comes with an electronic chip that transmits an immobilizer of your car. The chip is what allows the 500 to start and lock. If it gets wet it will cease to function.

You can try cleaning the internal electronics of your key fob using isopropyl alcohol or an electronic cleaner to see whether they're still in good condition. It is recommended to replace the key fob if it's submerged in salt water, rather than trying to repair it yourself.

While a replacement fob could cost a little money, it is a lot cheaper than paying for your Fiat 500 to be towed to the dealer for repair! You can also do it yourself by following just a few steps. Make sure you have the correct type of battery before attempting to open your key fob. You can find step-bystep directions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob communicates with the car's immobiliser unit to ensure your car is only able to start when the correct key is inserted. If the chip is damaged, or corrupted the car will not start regardless of what you do.

Damage to the water or a dead cell phone battery are the most frequent causes of an unreliable chip. Regardless of the reason, it is an ideal idea to hand the job to a locksmith, as they will be able to replace the chip for you quickly and at a cost-effective price.

If your key fob will not function after exposure to clean rain or tap water take the battery off. Clean the electronic component with a paper towel. If the key fob does not function, there is the possibility that it's malfunctioning components and need to be replaced.

Many people will seek out their dealer when they are in need of a new Fiat key fob, however it can be a expensive alternative. If you are seeking a cost-effective method to get your fiat key code key fob fixed make sure you contact United Locksmith. We have all the tools and expertise to repair your Fiat fob quickly and professionally. way.

Faulty Receiver Module

fiat 500 new key key fobs send an electronic signal to the vehicle, which will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However, there are some things that could cause the fob to cease working. This can be caused by a dead coin-battery or water damage, worn out buttons or a receiver issue signal interference, or a malfunctioning chip.

If the fob was placed in the pocket that has been subject to extreme trauma (such as being dropped on the hard floor or washed in the washer) the fob might not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept signals from a genuine key, and not from any other.

You'll need to replace the fob if this happens. A professional locksmith will manage the entire key replacement process including programming a new one for your 500. In fact, they can offer you a clone key that functions exactly the same way as your original fob (and costs only a fraction of the cost).