• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet come and go as they please without needing to let him in or out. They also help keep your cat from having to go to the bathroom inside the house.

Installing a cat flap into a door panel made of Upvc is much easier than in glass doors, however it requires some knowledge and the appropriate tools.

Measure the Door

The installation of a cat flap inside a door can be tricky however, as long as you choose the right type of cat flap, take your time and follow the directions provided, it should not prove to be a problem. We will show you how to draw the shape using the jigsaw to cut out the door's area. Then we will finish the job by affixing the flap. This will ensure that the flap stays in position and shields the doors from the damage caused by wind and rain.

The first step is determine the width of your pet to determine an accurate estimate of the size of cat flap installation in glass doors near me flap you will require. This will ensure that the flap is big enough to let your pet leave and enter the home without having to open and close the door every time, but it is also small enough to prevent the pet from straying too far in either direction.

If your kit comes with a drawing showing where to drill, then place it on the door, and then use a pencil around it. If your door has moulding or sill on the bottom edge of it ensure you have clearance from these as this will ensure your cat's safety and stop them from gaining access to your home.

Then put on your eye protection and a dust mask, and using a jigsaw, begin to cut along the line that you've drawn in. Don't press the blade too hard, as this can cause it to cut faster than you would like it to. If you own a square that you have cut, make use of it to verify that you're cutting properly and to make sure the hole is a good rectangle shape, once you are happy with this you can begin to remove the rest of the door material.

Draw a Line

The cat flap in upvc door panel flap is a great way to allow your pet to go out and in without having to worry about them being in the house with a visitor, or leaving unwanted gifts inside the home. It also prevents draughts, and keeps your home's temperature in check. Fitting a cat flap to your door might seem difficult to those who haven't done it before. A lot of people will hire a professional carpenter or joiner to do the work. It is an option, but you can do it yourself if your tools are right and the steps are adhered to.

This is much simpler to do on doors made of wood, however it is still possible with uPVC. However, you must be careful not to scratch the doors since this could make it impossible to claim your warranty. The first step is to take measurements of the door, making sure that it will be able to accommodate the new cat flap. This should be simple enough when you have the standard uPVC door, however you might need to take more care if using an alternative type of door as these are more difficult to cut than solid uPVC panels.

The next step is to measure the size of your cat's belly. This is the height between the floor and the underside of your cat's stomach. You will need to locate an area at the entrance that allows your cat flap installation near me to pass through comfortably. Once you have this information then you have to draw the area using pencil and a spirit level to be certain that the hole you will make will be a good fit for your cat.

Once you've marked the area, it's time to cut the hole. You will need a jigsaw and it is important that you take your time to ensure that the cuts are clean and smooth instead of rough and uneven, as it could cause damage to your door. It is also important to wear safety glasses and a dust mask when using the jigsaw, since breathing in the dust can be dangerous to your health. After you've finished the cutting, you'll need to smooth out the edges of the hole with sandpaper so that your cat flap can be fitted easily into place.

Cut a Hole

The process of fitting a cat flap to an existing door panel or double glazing sealed unit is quite difficult. You may be tempted to tackle the job yourself, but unless have plenty of expertise in DIY, it's recommended to hire an expert to complete the job for you. A faulty job can not only look ugly and unattractive, but could also be an security risk. It could let cold air to enter when the cat is outdoors and hot air out when it is inside.

The first thing to do is mark the location of the hole in the door with a pencil and a spirit level, this will ensure that it is positioned and that it runs in a straight line with other parts of the door. Make sure you have sandpaper on hand to smooth out any rough edges.

After the line is traced, you must cut the hole using the jigsaw. Remember to wear any safety equipment for working with the power tool. If you're worried about noise, you can get a cordless jigsaw which is quieter and easier.

It is best to only remove the material required to make the flap. It is important to leave a bit of material to make the wall thickness of the flap. However cutting away too much could cause problems or even damage the frame of the door.

If the upvc door is made of metal, or has a frame, it could interfere with the microchip flap. In this case, you will need to make an oversize hole to ensure that the metal doesn't get in contact with the walls of the flap.

If you are fitting the cat flap onto a upvc door or double glazed window cat flap with a frame made of metal, you'll need to talk to a professional who will provide you with a brand new pane of glass with the hole for the cat flap in it. This will be less expensive than trying to install a cat flap glass door installation near me flap inside an existing pane that was not designed specifically for this purpose.

Install the Flap

Cat flaps allow your pet to come and go as they please, giving them the freedom to lounge inside the house whenever they feel like it. However, if you have a uPVC door it can be difficult to fit a cat flap, especially in the absence of a glass pane that can be cut to accommodate one. If you are willing to install a half-glazed uPVC replacement panel, it is possible to add an additional cat flap. It's not a matter of cutting a hole into the door. You'll also need to do a few things to ensure that the door is secure.

A uPVC, GRP or composite door panel usually has an flimsy plastic outer layer joined to a soft polystyrene insulating core. The material is quite fragile and care must be taken when cutting through it to avoid causing damage. This type door comes with a template that can be used to cut the hole.

Once you have marked the location of the hole in your door, it's time to put in the cat flap itself. You can choose from a range of models, ranging from simple push-button units to microchip activated ones that only let your pet in. However, regardless of what type of cat flap double glazing flap you pick, it is essential to ensure that your cat is able to use the flap without becoming trapped in the weather.

It's a good idea select circular fittings instead of a square one, as circles can be more securely cut into the door glass. This is because square holes make glass more vulnerable to cracking if drills are used on it. This is also a safer option, as you won't have to drill into the toughened glass, which could shatter and harm your pet or family members. This is especially crucial if you have elderly or children living in your home who could be injured by glass shattering.