• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors wear out over time and need to be replaced. It is crucial to be able to match the dimensions of the handles you have previously replaced when replacing them.

The three measurements you need to examine are the top screw position as well as the key hole and lever sizes. Use the size guide to help with this.

Inline Lever/Lever

A lever door handle is a contemporary handle that can be put in on doors that are new or replacement. This kind of door handle is available in a wide range of designs and finishes. A variety of manufacturers provide this type of handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles made of uPVC/Composite are made of tough materials and are perfect for multi-point lock doors that require a robust design. The handles are inline and run with the same spindle as well as screw fixings. They can be easily fitted to doors made of uPVC/Composite, either new or old.

The design of the sprung lever allows the handle to be placed and angled to provide a comfortable grip and is suitable for all users. The handle has been endurance-tested to 200,000 cycles. This helps to ensure that the finish is of high quality and performance is maintained over time. The sprung lever can be shortened to fit the widest range of locks. This is particularly beneficial for narrower door frames where the cylinder is further back. A shorter lever is an ideal choice for doors where the latch can be activated by the thumb turn inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently from lever-type handles that are found on the majority of doors. These handle types can either work off one single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are typically used on UPVC double glazed window handles glazed doors and are available in a variety of variations and finishes.

The handles are available in a variety of finishes including White chrome, and Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with a high performance and long-lasting durability for its intended purpose.

All UPVC handle lever pads come with a spindle, screws and Replacement Door Handles can be installed on a uPVC door. The backplate fixation centres of 211mm permit a larger handle, which is usually beneficial when replacing an old or faulty multi-point door lock mechanism. The handle levers come with springs, which can solve the problem of handles for doors that slide out of their horizontal position when not being used.

When selecting the replacement UPVC handle and spindle, it is important to match the dimensions of the PZ of both the multipoint lock and the uPVC door. This measurement is often known as the "handle centre" or "cylinder centres which is a crucial aspect to match the correct handles.

Once you have decided on the correct size of PZ it is important to make sure that the push and lever pads are designed to match the American with Disabilities Act compliant handles that you need for your door. They are usually a square or round shape, with an internal lever and external push pad.

Most of the UPVC lever pads we sell are sprung, meaning that they return to their horizontal position when they are not in use, instead of hanging out and possibly securing in the frame. This keeps draughts out of the home. It is also the case that the majority of the UPVC lever pad handles and hinges are handed which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. Cylinder locks are operated by a key which unlocks the cylinder's case. This exposes pins that can be aligned to those in the lock and allow them to rotate the revolving camera, opening the door. Euro cylinders can be fitted with up to six pins, with both internal and external doors usually needing different levels of security.

The selection of a cylinder is essential. It's dependent on the amount of use your doors and handles will receive. For example, external doors must be secured with a higher security cylinder, while internal doors can be secured with the standard cylinder. Some cylinders have extra features that increase security, like anti-drill or anti bump properties.

To make sure that the euro cylinder is the correct size for your door, it must be measured accurately. The cylinder should be measured from the hole in the center of the fixing screw to each end of the cylinder, including the thumb turn if you have one. If you cannot measure with the lock in position, you can remove it. A cylinder that extends beyond the handle and escutcheon might be vulnerable to attacks such as snapping locks, so it is crucial that it is not too long.

The design of many modern cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease the chance of attack by forcing cylinders to rotate in a new direction. This can to deflect attacks and ensure your door is secure.

There are also cylinders that have been designed to resist snapping. This is a common occurrence on cylinders. A specific tool is used to break the break line of the lock, and then the front of cylinder is snapped off. This is a quicker and simpler method to gain access than through the use of a multipoint locking system. It also leaves less evidence of the burglary which could delay insurance claims.

Spring Cassette

This spring cassette sits inside the base of your door handle backplate providing a sprung solution that returns your multipoint lock handles to their normal position after using. The handles had no spring, and would slide when the locking mechanism was removed. This simple part is the most effective way to fix this problem. It also stops your door from becoming stuck in the closed or open position since they aren't easy to close manually.

These spring cassettes were designed to be used with sprung multipoint locks. They won't work with handles that aren't sprung and you'll need to cut a hole in the backplate to allow them to fit. (Please look at the image for a detailed diagram). They are a replacement for broken or missing cassettes within the backplates of door handles of many kinds of uPVC doors. They are fitted with a square cut out which can accommodate an 8mm spindle, and they are supplied individually.

These spring cassettes are a fantastic value for money solution to the issue of your bifold door handles handles sliding. They are simple to install and can extend the lifespan of your uPVC door. Contact us for more information about our selection of uPVC accessories and spares. We are always happy to offer professional advice and assistance you.